How to Open Joycon Without Screwdriver

Do you have a Nintendo Switch that you love to play, but the Joy-Cons are giving you fits? If so, then you’re in luck! There is a way to open up the Joy-Con without having to use a screwdriver.

  • Open up the back cover of the Joycon using a small screwdriver
  • Pry off the battery cover with a small screwdriver
  • Remove the screws holding down the circuit board
  • Carefully lift up the circuit board and remove it from the Joycon casing
  • locate the ribbon cable connecting the buttons to the circuit board and carefully disconnect it
  • You should now be able to access all of the internals of your Joycon!

How to Unscrew Tri Wing Screws Without Screwdriver

Tri-wing screws are often used in electronic devices, making them difficult to remove without the proper screwdriver. However, there are a few ways to remove tri-wing screws without a screwdriver. One way is to use a thin piece of metal, such as a paperclip, to wedge into the head of the screw.

Apply pressure and turn the paperclip until the screw loosens. Another way is to use two pens or pencils to create a makeshift tweezers. Insert the tips of the pens or pencils into the head of the screw and twist in opposite directions until the screw comes loose.

If you don’t have any tools on hand, you can also try unscrewing the tri-wing screws with your fingers. This will require some patience and dexterity, but it is possible to do. Start by inserting your fingernail into the head of the screw and twisting gently.

If that doesn’t work, try using a small rock or other hard object to apply pressure while you twist with your fingers. With enough persistence, you should be able to loosen the screw enough to remove it by hand.

Tri Wing Screwdriver

A tri-wing screwdriver is a type of screwdriver that is used to remove screws that have three raised sections on the head, known as wings. These types of screws are often found in electronic devices, such as game consoles and handheld electronics. The tri-wing screwdriver has a triangular tip that fits into the slots on the head of the screw.

To use a tri-wing screwdriver, start by inserting the tip into one of the slots on the head of the screw. Apply pressure to the handle of the screwdriver and turn it counterclockwise to loosen the screw. Continue turning until the screw is loose enough to be removed by hand.

Repeat this process for any other tri-wing screws that need to be removed. When you’re finished, reinsert any screws that were removed and tighten them securely before putting your electronic device back together.

Joycon Screwdriver

If you’re a Nintendo Switch owner, chances are you’ve had to deal with Joy-Con drift at some point. For those unfamiliar, Joy-Con drift is a problem that causes the Switch’s controllers to register input even when they’re not being touched. This can be extremely frustrating, especially if it happens in the middle of a game.

See also  How to Jump a Starter With a Screwdriver


There are a few things you can do to try and fix Joy-Con drift, but one of the most effective methods is to use a screwdriver. Yes, that’s right, a screwdriver. Here’s how it works:

1) Take your Joy-Cons apart and remove the screws from the backplate using a Phillips #0 screwdriver. Be careful not to lose any of the small screws! 2) Using a flathead screwdriver, gently pry up on the black tab that’s holding down the joystick assembly.

There are four of these tabs in total (one for each direction). 3) Once all four tabs have been lifted, carefully remove the entire joystick assembly from the Joy-Con housing. You may need to wiggle it around a bit to get it out.

4) Take a look at the gold contact points on both the joystick assembly and the Joy-Con housing. If there is any dirt or debris build-up on either of these surfaces, use a cotton swab dipped in rubbing alcohol to clean them off. Make sure they’re completely dry before proceeding.

How to Open a Gameboy Without a Triwing Screwdriver

Nintendo’s Gameboy is one of the most popular handheld gaming consoles of all time. Released in 1989, the original Gameboy quickly became a must-have device for gamers around the world. While the console has seen several iterations over the years, the basic design remains largely unchanged.

One of the most notable features of the Gameboy is its triwing screws, which are used to keep the device closed and secure. In order to open a Gameboy, you will need a triwing screwdriver. These specialized screwdrivers can be found at most hardware stores or online retailers.

Once you have your screwdriver, simply insert it into each of the three screws on the back of the device and twist counterclockwise until they are loose. With the screws removed, you should now be able to gently pry open the casing and access the internal components of your Gameboy. Opening up your Gameboy is relatively simple and only requires a few tools.

However, it is important to exercise caution when doing so as there are delicate electronic components inside that could be damaged if handled improperly. If you’re not comfortable opening up your device, there are plenty of tutorials online that can walk you through the process step-by-step.

How to Take Apart a Joycon

Assuming you mean how to disassemble a Nintendo Switch Joy-Con controller: The first step is to remove the back plate of the Joy-Con. There are four screws that need to be removed in order to do this.

Once the back plate is off, you will have access to the battery. Next, remove the screw that holds down the battery. Be careful when removing the battery, as there are small wires attached to it.

See also  What Screwdriver to Open Nintendo Switch


Now that the battery is out, you can start removing the buttons. The “+” and “-” buttons are held down by small screws, so remove those first. Then, use a flathead screwdriver or something similar to pry up the “+” and “-” buttons.

Be careful not to break them! After that, the shoulder buttons and main face buttons can be pried up with ease. There are two ribbon cables connecting the Joy-Con halves together; one for audio and one for rumble.

Gently pull on each cable until they come undone from their connectors. And that’s it! Your Joy-Con is now successfully disassembled.

How to Open a Ds Lite Without a Tri Wing Screwdriver

If you’ve ever found yourself in a situation where you need to open a DS Lite but don’t have a tri wing screwdriver on hand, don’t worry – there’s an easy way to do it without one. All you’ll need is a small Phillips head screwdriver and a pair of needle nose pliers. First, remove the four screws from the back of the DS Lite using your Phillips head screwdriver.

Next, use your needle nose pliers to carefully pry open the back cover. Once the cover is off, you’ll be able to access the battery compartment and any other internal components. With just a few simple tools, you can easily open up your DS Lite – no tri wing screwdriver required!

Y00 Screwdriver

Assuming you would like a blog post about the Y00 Screwdriver: The Y00 Screwdriver is a versatile tool that can be used for a variety of tasks. It features a durable design that is built to last, and it has a comfortable grip that makes it easy to use.

The screwdriver also has a magnetic tip that helps to keep screws in place while you work.

1.5 Tri Wing Screwdriver

A Tri-Wing Screwdriver is a type of screwdriver with three wing-shaped blades, designed to fit the screws used in Nintendo products. The name “Tri-Wing” comes from the Japanese manufacturer Nintendo, who created this type of screwdriver. The Tri-Wing Screwdriver is not a standard size or shape, so it cannot be used for anything other than Nintendo products.

It is important to have the correct size and shape of screwdriver when working on any electronics, as using the wrong size or shape can damage the screws or product. If you are looking for a Tri-Wing Screwdriver to use on your Nintendo products, you can find them online or at some stores that sell electronic supplies.

How to Open Joycon Without Screwdriver

Credit: www.nintendolife.com

What Can I Use to Unscrew My Joycons?

If your Joycons are attached to your Switch and you want to remove them, the best way to do so is by using the release button on the back of the Switch itself. This will detach the Joycons from the console without damaging them. However, if for some reason you can’t use the release button or your Joycons are already detached from the console, then you can use a small Phillips head screwdriver to unscrew the four screws on each Joycon (two on top and two on bottom).

Be careful not to strip these screws, as they are very small. Once all eight screws have been removed, you should be able to carefully separate the two halves of each Joycon.

See also  How to Open a Car Trunk With a Screwdriver

How Do You Unscrew Joy-Con Screws?

There are four screws on the back of each Joy-Con, two on the top and two on the bottom. These screws hold the Joy-Con shells together. You will need a Phillips head screwdriver to unscrew them.

To remove the Joy-Con shells, start by removing the top two screws. Then, slide the Joy-Con up and out of its bottom rail. Be careful not to lose any of the small springs or plastic pieces that are attached to the bottom of the Joy-Con.

With the Joy-Con removed from its bottom rail, you can now access the remaining two screws. Remove these screws and then carefully separate the two halves of the Joy-Con shell. Again, be careful not to lose any of the small springs or plastic pieces that are attached to either half of the shell.

How Do I Unscrew a Joy-Con Switch?

Assuming you would like tips on how to remove the Joy-Con controllers from the Nintendo Switch console, here are a few easy steps: 1. First, make sure that your Switch is turned off. If it’s not, go ahead and turn it off now.

2. Locate the small black release button on the back of the Switch near where the Joy-Cons attach. 3. Press and hold this button while simultaneously sliding each Joy-Con controller away from the body of the Switch. They should come right off with a satisfying “click.”

4. That’s it! You’ve now successfully removed your Joy-Cons from your Nintendo Switch console.

Remove A Stripped Joy-Con Screw With Left Handed Bits – No Damage

Conclusion

Joycon controllers are the detachable gamepads for the Nintendo Switch. They come in a variety of colors, and they’re pretty easy to take apart and put back together… as long as you have a screwdriver. If, for some reason, you don’t have a screwdriver handy (or if you’re just feeling brave), there’s actually a way to open up your Joycon without one.

All you need is a small, sharp object like a penknife or an unfolded paperclip. Here’s how to do it: 1) Locate the small hole on the back of the Joycon near the top.

This is where the screws are hidden. 2) Insert your tool into the hole and apply pressure until you feel the screw start to loosen. Be careful not to push too hard, or you might damage the controller.

3) Repeat this process for all three screws. Once they’re loose, you should be able to pull off the backplate with ease.

Leave a Comment