It is a common misconception that one needs to drill and tap a shotgun in order to install a scope. This is not the case. In fact, it is possible to install a scope on a shotgun without drilling and tapping at all.
There are several methods of doing this, but the most popular is to use bases and rings that clamp onto the barrel. This method is perfectly adequate for most purposes, and it has the advantage of being easily reversible if you decide later that you don’t want a scope after all.
If you’re a shotgunner, sooner or later you’re going to want to add a sling or some other accessory. That usually means drilling and tapping the gun for screws. Here’s a quick rundown on how to do it.
First, you’ll need to choose the right size drill bit. For most #8 or #10 screws, a 1/16″ bit will work fine. If you’re using larger screws, you’ll need a bigger bit.
Next, mark the spot where you want to drill the hole. It’s important to be as precise as possible here, because if the hole isn’t perfectly straight, your screw might not go in properly (or worse, it could strip out the threads). A good way to mark the spot is with a center punch; just tap it lightly with a hammer to make an indentation in the metal.
Now it’s time to actually drill the hole. Start with a slow speed and gradually increase it as needed. Don’t apply too much pressure – let the drill do the work.
Once the hole is drilled all the way through, switch to a slightly smaller bit and enlarge the opening just enough so that your screw can start threading into it easily.
Drill And Tap Shotgun Receiver
A drill and tap shotgun receiver is a great way to add a scope or red dot sight to your shotgun. This type of receiver allows you to keep the original iron sights on your gun, but also gives you the option to add a optics. Here are some instructions on how to do this upgrade:
1) First, you will need to remove the old rear sight from the shotgun. This is usually done by unscrewing two screws that hold it in place.
2) Next, use a drill bit that is slightly smaller than the diameter of the new sight’s base.
Drill a hole in the center of the forward portion of the shotgun’s receiver, being careful not touch any other part of the gun while doing so.
3) Once the hole has been drilled, thread it with a tap handle and appropriate size tap for your new sight’s base. Be sure to clean out any metal shavings before proceeding.
4) Now it’s time to install the new sight onto the receiver. Most aftermarket scopes or red dots come with their own mounting hardware, so simply follow those instructions (usually just 2-3 screws). If not, then you can find many different types of Weaver or Picatinny rail sections that will clamp onto your receiver – these usually just require 4 screws for installation.
5) That’s it! You’re now ready to shoot with improved accuracy thanks to your new optic!
Credit: www.rem870.com
What Shotguns are Drilled And Tapped?
Drilled and tapped shotguns are those that have holes drilled into the receiver, usually near the sight, so that a scope or other optic can be mounted. This allows for greater accuracy when shooting, as the shotgun’s iron sights are not obstructed by the optic.
Who Can Cut a Shotgun Barrel?
A gunsmith or qualified machinist can cut a shotgun barrel. The process requires special tools and knowledge of firearms safety. Cutting the barrel too short can make the gun dangerous to operate.
How Much Does It Cost to Re Sleeve a Shotgun?
Shotgun resleeving is a process by which the bore of a shotgun barrel is relined with a new, thicker wall of metal. The purpose of this is to increase the longevity and performance of the shotgun. Resleeving can be done on any type of shotgun, but it is most commonly seen on competition shotguns that are fired frequently.
The cost of resleeving a shotgun will vary depending on the gunsmith you take it to and the type of metal used for the new sleeve. Generally speaking, you can expect to pay between $200 and $400 for this service.
How Much Does It Cost to Sight in a Gun?
If you’re a hunter or competitive shooter, at some point you’re going to need to zero, or sight in, your rifle. The cost of sighting in a gun will depend on a few different factors, but the average price is between $50 and $100.
This cost includes the price of ammunition, which is typically around $20 for 20 rounds.You’ll also need to pay for a target, which can be anywhere from $5 to $15. And finally, if you’re not comfortable doing it yourself, you’ll have to pay someone else to do it for you – usually a gunsmith or range officer. The good news is that once you’ve sighted in your gun, you shouldn’t have to do it again unless you make significant changes (like changing the type of ammo you’re using).
So even though the initial cost may seem high, it’s really only a one-time expense.
How To drill and tap for a scope mount
Conclusion
If you’re looking to drill and tap a shotgun, there are a few things you need to know. First, you’ll need to determine the size of the hole you need to drill. Second, you’ll need to figure out the depth of the tap.
And finally, you’ll need to determine the proper thread size for your application. With these three things in mind, let’s take a look at how much it costs to drill and tap a shotgun.
